silencers

英 [ˈsaɪlənsəz]

美 [ˈsaɪlənsərz]

n.  (发动机的)消音器; (枪支的)消音器
silencer的复数

柯林斯词典

• N-COUNT (枪支的)消音器
  Asilenceris a device that is fitted onto a gun to make it very quiet when it is fired.
  1. ...a pistol that was equipped with a silencer.
     装了消音器的手枪
• (汽车排气管上的)消音器
  Asilenceris a device on a car exhaust that makes it quieter.

in AM, use 美国英语用 muffler

双语例句

• A substructure method and a dual reciprocity boundary element method ( DRBEM) are applied to calculate four-pole parameters and transmission loss of ducts and silencers with complex flow.
  将子结构法和双倒易边界元法联合应用于预测具有三维复杂流存在时管道和消声器的四极参数与传递损失，阐述其基本原理与数值过程。
• The paper describes the structure and design features of AFP, AXP and XXP type boiler blow off silencers.
  介绍了AFP、AXP、XXP型锅炉排汽消声器的结构原理和设计特点。
• Comparisons of transmission loss predictions with experimental results for straight through perforated tube dissipative silencer illustrated that FEM can predict acoustic characteristics of perforated tube silencers accurately.
  直通穿孔管阻性消声器传递损失的有限元预测结果与实验测量结果吻合很好，表明了三维有限元法预测穿孔管阻性消声器声学性能的适用性和精度。
• On this basis structural optimization of two silencers are put up, and specific design scheme and structural dimensions are determined. Process water silencer and put up experimental research.
  在此基础上进行了两种消声器的结构优化设计，并确定了具体的设计方案和结构尺寸，设计加工了可变频消声器的原理样机，进行了实验研究。
• To do so, secure the rear silencers with a transmission jack.
  为此，用变速箱千斤顶固定尾部消音器。
• Three-dimensional FEM is developed to predict and analyze the acoustic attenuation characteristics of perforated tube silencers.
  三维有限元法被发展用于预测和分析穿孔管消声器的声学性能。
• The sound source and microphones are arranged reasonably, so that the transmission loss of silencers with high gas flow velocity and the flow generated noise inside the silencer can be measured on the test-bed.
  设计并搭建了消声器声学性能测量试验台，合理布置声源及传声器，使该台架可用于高流速情况下消声器传递损失以及消声器内流噪声的测量。
• The rear silencers can be replaced individually by disconnecting the system.
  断开系统后，可以单独更换尾部消音器。
• Finally, the transmission loss results of straight-through perforated tube silencers with partially-perforated tube and divided tube are calculated and analyzed. Some conclusions are drawn according to these results, which supply guidance for silencer designs.
  最后计算并分析了中心管部分穿孔和带有分隔管的直通穿孔管消声器的传递损失，得出一些结论，为消声器设计提供指导。
• The paper gives a method about the integrative drive of the CAD software for tractor exhaust silencers and a method for DOS change.
  介绍了拖拉机排气消声器CAD软件的一体化驱动方法和“状态切换”方法。